PIC compiler for hobbyist
Curious what other hobbyists are using for a PIC compiler: Microchip XC, MikroE's microC, or some other compiler. Just getting started with PICs and having trouble deciding which IDE / compiler I want...
View ArticleI need timer to be count with seconds (MM : SS) for MiKroC Code
I need timer to be count with seconds (MM : SS). in place of HH:, I need to be MM: and in place of HH:, need SS: How could I write? Mods Note: Please don't hijack other member's thread, now you have...
View ArticlePICKit 2 Clone Setup
Connected it to 10F200 on breadboard. It is not reading the device. What setting do you use in the PICKit 2 software?
View ArticledsPIC30F4011 to control the output voltage of a SMPS IC
Hello All, I wish to use the dsPIC30F4011 in my application. There are two regulators I have to use in my application. The one is from TI LM25117-Q1, which is Step-down regulator . The dsPIC is a 40...
View ArticleProgramming Microprocessors
Hello, this is my first time on these forums so i don't know if i'm doing it right. For the last few days i've been trying to get into microprocessors, however i just don't know where to start. My...
View ArticleI Need Guidance on Genuino Uno?
Hello Guys, I'm here to find the best guidance of my question. I'm working on an arduino robotic project.And I researched about the arduino. But my problem is that, my project required Genuino Uno and...
View ArticleArduino Due & UNI-T UTD2025CL Digital Oscilloscope
Hi guys, I have long since been interested in the subject of electrical, electronics engineering. But being a professional IT developer, I only got down to it lately. Due to budget constraints, I did...
View ArticleBMP 280 exact Altimeter readings.
Hi, I was just going through this pressure sensor tutorial. What I want to know is how can I set the exact altimeter in my readings depending upon my different geographical place ? or may be if I am...
View ArticleGray code inputs to seven segment output using uc
I have a 4 gray code inputs and want to feed it to seven segment display using micro controller . Can anyone suggest how to proceed. thank you
View ArticleNo PLC output to valve when program is running
Hi, 2 hopper scale valves are controlled by a PLC (Siemens). The plc controls the pneumatic directional control valves and the directional control valves control the opening and closing of the large...
View Article16 to 2 wire communication via RS485 communication
hello I have a project where I take 16 wires as inputs and convert it into 2 wires Rs485 communication and again decode it from Rs485 2 wires into same 16 wires. I am thinking of giving 16 inputs to...
View ArticlePIC 12F675 ADC Circuit understanding: Input signal impedance.
I am struggling trying to understand the input impedance of the signal to a PIC12f675 ADC. The circuit works fine as far as I can tell, but I want to know more or maybe I just want some assurance that...
View ArticlePIC Assembler Observation
This tutorial covers about 35 to 45 areas of Baseline assembler. If somebody does the Midrange assembler lessons also. You end up with sort of a 'PIC Toolbox'.. A concise knowledge of what can be done...
View ArticleAssembler 12F508 Special Features
'Onward they rode through the Valley of Death. The gallant 600.'-Tennyson Onward I go to Lesson 7 First subject is Sleeper Mode. Then Wake Up on Change Watchdog Timer and Osillator (Clock)...
View ArticleDesigning a simple alarm circuit using microcontroller
I am designing a simple alarm circuit using PIC12F629 and I need advise from this forum of experts on how I could accomplish and fine tune the circuits. The alarm input set the GP0 High and flashes an...
View ArticleHow receieving values more than 255 by Arduino uno
Hello, I have a problem when I am sending values from processing to the Arduino , I can't read the values more than 255, I used the serial port, thanks
View Articlebuck converter using atmega328p
Hi all I have recently planned to install solar panels at my home.I have planned to make the charge controller myself.I planned to be it as MPPT controller.For the controller,I will use atmega328p.It...
View ArticlePICKit 2 Clone Reading PIC
Having a little difficulty getting started here. Using PICKit 2 Software and/or MPLAB 8.40 Getting calibration warning. It can't read PIC. Anybody know how to fix this?
View ArticleWhat is the clock generating diagram I2C protocol while sending Data &...
I need to communicate between Micro controller & FPGA(frame grabber card) using I2C protocol. I want to know if data 5 has been sent from Master (Controller) what will be the clock generation....
View ArticlePICKit 3 Programming Problem Solved
'Read has changed program' This is in IPE. That was causing the problem. This is going by Memory View-Program Memory You click Yes and it changes the compiled hex you have loaded into what you read off...
View Article